Hardwood floor refinishing in Burlington, NC

If your hardwood is dull, scratched or stained, you may not need new floors. Sanding and refinishing can make old boards look new.

Sunlit living room with wood plank flooring and a stone fireplace
Call (336) 654-1130Serving Burlington and nearby Alamance County townsEstimates scheduled by phone

Why refinish instead of replacing

Solid hardwood is thick enough to be sanded many times. A good refinishing job removes the top layer, with its scratches, dents and worn finish, and exposes fresh wood below. A new stain and sealer then bring out the grain and protect it. The result looks like a new floor at a fraction of the cost of tearing out and replacing.

Many houses in the Burlington area have original oak or pine floors under carpet or old vinyl. Pulling up the carpet and finding good wood is a very common story. Whether the boards can be saved depends on their condition and thickness.

Can your floor be refinished?

  • Is it solid hardwood, or engineered with a thick enough wear layer?
  • Are the boards flat and firmly nailed down, with no severe cupping?
  • Are stains from pet accidents or water limited to a few areas?
  • Is there enough wood left above the nails to sand safely?
  • Is the finish worn in traffic areas but the wood still sound?

The refinishing process

  1. Remove furniture, rugs and baseboard shoe molding.
  2. Repair loose boards, fill gaps and replace badly damaged boards.
  3. Sand with progressively finer grits to remove the old finish and level the surface.
  4. Vacuum and clean dust completely from the floor, walls and trim.
  5. Apply stain if you want a color change, or keep the natural tone.
  6. Apply several coats of finish with drying time between coats.
  7. Allow the floor to cure before returning furniture.

Stain and finish choices

Natural tones show off the wood. Darker stains give formality, though they show dust and scratches more. Gray and whitewashed tones are popular but need careful sample testing, since results vary by species. Water-based polyurethane dries quickly, has less odor and stays clear. Oil-based finishes add an amber warmth and are durable but take longer to cure. Hardwax oils give a natural look and are spot-repairable.

We recommend testing stain samples on the actual floor in a hidden spot, since every board takes color differently.

Dust, odor and curing

Modern sanders have dust containment, but some fine dust will travel. We seal doorways and vents to reduce it. Finishes have odor during application and curing. You may want to stay elsewhere for a day or two, especially with sensitivities. Furniture should not go back until the finish is hard, and rugs should wait longer so the surface does not trap moisture.

Maintaining the result

Use felt pads on furniture legs. Sweep or vacuum regularly. Clean with products designed for hardwood. Avoid steam cleaners. A maintenance coat every several years can refresh the surface without full sanding. For new installations and repairs see hardwood flooring installation and hardwood flooring.

Common problems we see

Gray patches near pet doors and sinks usually mean water has soaked into the wood and darkened it. Sanding may remove the discoloration, or it may not, in which case we can bleach or replace a few boards. Wide gaps between boards, especially in winter, are normal movement. Deep gouges can be filled or planed. Cupped boards need the moisture source identified before refinishing, or the problem will come back.

Timing your project

Refinishing works best when you can leave the floors alone for several days. Spring and fall have moderate humidity that helps finishes cure evenly. Summer humidity slows drying, and winter heating can cause boards to shrink. We schedule around these factors where possible.

Choosing a sheen

Sheen affects how scratches and dust show. Satin hides wear better than gloss, and matte hides it better still. High gloss shows every flaw but gives a formal look. Many people choose satin for living areas. Test the finish on a sample board in the room's light before committing.

Questions we hear on the phone

Short answers to what callers ask most. Call if yours is not here.

How many times can a hardwood floor be sanded?

Several times for solid hardwood, depending on thickness. We measure what is left.

Will deep pet stains come out?

Some do, some do not. We tell you what to expect.

How long does refinishing take?

A few days for one or two rooms, plus curing.

Can I change the color?

Yes, refinishing is the time to do it.

Tell us about your project.

Call and we will schedule your estimate.

Call (336) 654-1130
Call (336) 654-1130