Shower door and faucet installation in Burlington, NC
Doors, faucets and valves are the parts of a shower you touch every day. They need to fit well and work smoothly.

Shower doors
A shower door is more than glass on a track. It controls splashing, affects how big the bathroom feels and sets the look of the whole space. Framed doors have metal edges and are the most economical. Semi-frameless doors have a metal header and track with frameless glass panels. Fully frameless doors use thick glass with minimal hardware and give a clean, open look.
Fit is the biggest factor. Tile walls are not perfectly plumb, and a glass door must be set to the real opening, not to the ideal one. We measure carefully, order the glass to fit and install it with shims, silicone and the right hardware.
Types of enclosures
- Hinged doors: swing open, ideal for walk-in showers with enough space.
- Sliding bypass doors: save space in tub alcoves.
- Fixed panels: a single sheet of glass with an open entry, popular for walk-in showers.
- Pivot doors: swing both ways for flexible access.
- Neo-angle and corner enclosures: for corner shower layouts.
Valves, faucets and trim
Behind every shower handle is a valve, and valves wear out. If your shower runs hot and cold, leaks at the handle or has low pressure, the cartridge or valve may need replacing. A new valve with pressure balancing or thermostatic control improves comfort and safety. Showerheads, hand-held sprayers and rain heads are simple additions once the valve and plumbing are ready.
For sinks, we install new faucets, replace supply lines and shutoff valves and check the drain assembly. When the plumbing needs more than simple replacement, we work with the appropriate trade.
Installation steps
- Confirm the product choices and finish, such as chrome, brushed nickel or matte black.
- Measure the opening and order glass or the product to fit.
- Shut off water and remove the old door, valve trim or faucet.
- Prepare the surface, repair any damage and install new components.
- Seal the glass and hardware with silicone, and install the sweep and seals.
- Test for leaks and proper operation, then adjust.
- Review cleaning tips and warranty details.
Keeping glass clean
Hard water leaves spots. A squeegee after each shower, a gentle cleaner and an occasional vinegar solution on metal parts help a lot. Protective coatings on the glass can reduce spotting. Check seals once a year. If you are updating the whole shower, see walk-in shower conversion and shower restoration.
Matching finishes
Matching metal finishes across faucets, showerheads, door hardware and towel bars makes a bathroom feel put together. Mixed finishes can look intentional if done carefully, but a bit of planning prevents accidental mismatch. Bring samples when you shop and tell us what you chose.
Troubleshooting before replacing
If a shower door sticks, the track may be dirty, or the rollers may be worn. If a faucet drips, a cartridge, washer or seat may be worn. If water pressure is low at one fixture, an aerator or showerhead screen may be clogged with mineral deposits. These are easy fixes. We check them before suggesting replacement, because sometimes a small repair is the right answer.
Hard water
Water in much of the Piedmont is relatively soft compared with some regions, but mineral buildup can still occur. Wipe fixtures and glass dry, and use a mild descaler when needed. Finishes like brushed nickel and matte black hide spots better than polished chrome.
Safety glass and hardware
Shower glass should be tempered, which breaks into small pieces instead of sharp shards. Hardware, including hinges and handles, must be rated for the glass weight. Frameless doors depend entirely on a few hinges and clamps, so quality matters. Check screws annually and tighten any that have loosened.
Warranty and replacement parts
Keep the model numbers of faucets and doors. Parts for common brands are easy to find years later, and a record of the model saves time if a cartridge or roller needs replacing.
Questions we hear on the phone
Short answers to what callers ask most. Call if yours is not here.
Can you install a door I bought myself?
Yes, as long as it fits the opening. We check before starting.
Do frameless doors leak?
They can if poorly fitted. Careful installation and seals keep splashing in check.
Can you replace only the valve trim?
Yes, if the valve behind it is in good condition.
How long does it take?
Most door and faucet installs take a day or less.
Related services
Tell us about your project.
Call and we will schedule your estimate.