Trim and molding installation in Burlington, NC

Trim is the detail that makes a room feel finished. Good trim frames the walls, hides gaps and gives a house its character.

Call (336) 654-1130Serving Burlington and nearby Alamance County townsEstimates scheduled by phone

Why trim matters

Trim does a few jobs at once. It covers the joint between the wall and the floor, the wall and the ceiling, the wall and the door. It protects corners from damage. And it gives a room its style. A plain flat baseboard reads modern. A tall, stepped baseboard with a cap reads traditional. Crown molding adds formality. Wainscoting adds depth and texture and protects lower walls from scuffs.

A common remodeling mistake is spending on a new floor, new paint and new fixtures and keeping old, worn trim. The room never quite looks finished. A few hundred feet of fresh trim can do more for the look than almost anything else you could add.

Types of trim and molding we install

  • Baseboards: from simple flat to tall and layered.
  • Door and window casings: with or without decorative headers.
  • Crown molding: at the ceiling line, in single or built-up profiles.
  • Chair rail and picture rail: horizontal accents in dining rooms and hallways.
  • Wainscoting: paneled, board-and-batten or shiplap for the lower wall.
  • Shoe and quarter-round: for covering gaps where floors meet baseboards.
  • Mantel and fireplace surrounds: built or refinished to suit the room.

The skill is in the joints

Walls and floors are never perfectly straight. Corners are rarely exactly ninety degrees. Good trim carpentry means cutting each joint to fit the corner as it actually is, not as it should be. Inside corners are often coped, with one piece cut to fit the profile of the other, instead of mitered, because coped joints stay tight as wood moves. Outside corners are mitered and glued. Crown at the ceiling needs careful measuring and often a bit of caulk and patience.

Painting also matters. We prefer to prime and paint trim in the shop or on sawhorses before installation, then fill nail holes, caulk and touch up after. That gives a smooth finish and sharp lines.

How the job goes

  1. Walk the house and decide which rooms get which profiles.
  2. Measure and order material, with extra for waste and mistakes.
  3. Remove old trim carefully so the wall surface is not damaged more than necessary.
  4. Patch and prepare the wall, adding blocking where needed.
  5. Cut and install pieces, nailing into studs and gluing joints.
  6. Fill nail holes, caulk seams and sand where needed.
  7. Prime and paint, or stain and finish, and clean up.

Pairing trim with other work

Trim goes in last, after flooring, drywall and painting of the main surfaces. If you are installing a new floor, we install baseboards and shoe molding after. If you are painting, we often combine the two jobs, see interior painting. In older houses we match existing profiles when possible, and when it is not, we choose a replacement that blends.

Choosing profiles by room and ceiling height

Baseboards should look proportional to the room. In a standard eight-foot room, a baseboard of about four to five inches is common. Taller ceilings take larger trim. Door casings should be similar in weight to the baseboard so the pieces look related. Crown molding looks best when its size scales with the ceiling height, and low ceilings often look better with a simpler, smaller crown or none at all.

In older homes, original trim may be wide and detailed. If most of it survives, we match it where we can and reuse salvaged pieces where possible. Replicating a long-lost profile often means a custom knife at a mill, which we can arrange if the house justifies it.

Materials

Pine and poplar are common paint-grade woods. Oak and other hardwoods are chosen for stained trim. MDF is smooth and takes paint well but should not be used where it will get wet. PVC trim suits bathrooms and exteriors because it does not swell with moisture.

Questions we hear on the phone

Short answers to what callers ask most. Call if yours is not here.

Can you match old baseboards?

Sometimes with stock profiles or custom-milled pieces. We look at the existing trim and tell you what is possible.

Is crown molding worth it?

It adds character, especially in rooms with higher ceilings. We discuss proportions with you.

Do you paint the trim too?

Yes, finishing is part of the job. Call and describe the scope.

Can trim hide damage?

It can cover small gaps. Larger problems should be repaired first.

Tell us about your project.

Call and we will schedule your estimate.

Call (336) 654-1130
Call (336) 654-1130